Sanyo Soundbar Remote Control Codes

Remote codes for Sanyo soundbars. A Sanyo soundbar can be controlled with any universal remote control if you have the correct programming guide and the specific remote codes for the sound bar. A Sanyo soundbar can be controlled or programmed to work with a CAB, SAT, or Universal Remotes.

Remote Codes for SANYO SoundbarsRemote Codes for SANYO Soundbars

Program your universal remote control to an Sanyo Sound Bar. Use the following 3 and 5 digit remote codes.

Sanyo Soundbar 3 Digit Remote Control Codes:
590
611
627
661
683

Sanyo Soundbar 5 Digit Remote Control Codes:
20047
10154
10159
10051
10250
20035
30189
30531
20081
21593
20593
20000
20039
20149
21781

The above codes have shown to work with Sanyo soundbar models FWSB415E, FWSB405FS, FW405SB, and FWSB405F.

If these remote codes do not work, try the code search on your CAB or SAT remote…

ATT Remote RC7X:
Program your Sanyo soundbar to the RC7x remote control:
Follow the instructions by going to…
-MENU
-SETTINGS
-SETTINGS & HELP
-REMOTE CONTROL
-AUDIO DEVICE

With DIRECTV or ATT as your cable with DIRECTV Remote Control:
-Sanyo Soundbar on
-Volume up but muted
-AV1 or AV2
-Press and hold MUTE and SELECT for 2 blinks
-Enter 9 9 1 and wait 2 blinks
-Enter 3
-Press and release VOL UP
-Point the remote at the Sanyo soundbar and keep pressing and releasing the CH UP key
-When the volume changes, press select to lock in code.

If DIRECTV remote controls the power of the Sanyo soundbar but not volume, try this:
-AV1 or AV2
-Press and hold MUTE & SELECT
-Wait for 2 blinks and release
-Enter 9 9 3
-Press SELECT

Code Search using silver Comcast remote with a red OK/Select button:
-Turn on your Sanyo sound bar
-Press Aux once
-Press and hold Setup until the key blinks twice
-Release Setup
-Enter 9 9 1 3
-The Aux key will blink twice
-Press Power and aim the remote control at the Sanyo sound bar
-Press CH+ until the sound bar turns off
NOTE: In the code search mode, the remote control will send IR codes from its library to the selected device.
-Press Setup once to lock in the code
-The Aux key will blink twice

With a Comcast Xfinity remote with the red ok button:
-Press aux then press and hold setup till it blinks twice
-Enter code from list above
(This code will control the volume)

With a Comcast Xfinity remote with the red ok button – To lock to the Sanyo soundbar:
-Hold setup till it blinks twice
-Enter 9 9 3
-Press aux
To take the lock off and make it independent of each device:
-Hold setup till it blinks twice
-Press 993 then vol+ once
(Now you can select each device you want to change the volume for)

The above CODE SEARCH (Remote Control Programming) methods are written for Comcast and DIRECTV remotes but can be used and tried with ANY universal remote. The code search methods above are examples of how to get your current remote to control your Sanyo soundbar.

Need more help programming your Universal or CAB SAT remote to your Sanyo soundbar? Please leave your questions below and we will be happy to assist.

3 thoughts on “Sanyo Soundbar Remote Control Codes”

  1. Hi i have a UR5L-9020L REMOTE AND A SANYO SOUNDBAR FWSA205E. I LOST THE REMOTE AND NEED HELP PROGRAMMING IT TO MY REMOTE THANK YOU.

  2. Hi I have a sharp aquos QB118WJSA remote control and I have the SAYNO – FWSB426F sound bar I lost the remote for it can you help with the code for this remote the sharp

  3. I just bought a Inteset universal remote and it doesn’t list a remote code for my Sanyo nc302 soundbar.

Leave a Comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.